South Carolina Packaged Equipment Contractor License

Important changes in the 2021 IMC include:

• Clothes dryer exhaust terminals required to be at least 3 feet from any opening into a building.
• Polyurethane spray-applied foam on the exterior of ducts in attics and crawl spaces required to meet specific smoke and flame index limits.
• Fire and smoke dampers must be provided with approved access for inspection and maintenance.
• Refrigerant tables updated to include new refrigerants.
• Addition of condensate termination identification markings and discharge restrictions.
• Approved factory-built combination intake/exhaust terminations permitted, relaxing separation requirement.
• 30% reduction in minimum mechanical ventilation for whole-house balanced ventilation systems.
• Continuous operation requirement for manicure and pedicure station exhaust systems.
• Grease duct horizontal cleanout required within 3 feet of a horizontal discharge fan.

Key changes in the 2021 IFGC® include:

• The termination of concealed condensate piping requires marking to indicate if it is the primary drain or the secondary drain.
• Press-connect joints are acceptable for high pressure (over 5 psig) applications indoors.
• Commercial cooking appliances are not allowed within dwelling units.

Uses:

• Sizes metal ducts, lined metal ducts duct board airways, and wire helix flexible ducts.
• Converts round shapes to equivalent rectangles.
• Correlates available pressure with total effective length and friction rate (Manual D sizing calculations).
• Converts velocity into velocity pressure and vice versa.
• Corrects for altitude and temperature

The New Fifth Edition of Manual N® details the load calculation procedure that addresses the advances in the commercial construction industry: new materials, methods of assembly, and operational requirements. It provides instruction to help contractors and designers satisfy new, and often conflicting, energy, ventilation, and comfort requirements. The new Manual N is divided into four sections providing both a quick and comprehensive procedure for commercial load calculation.

• Section 1 Abridged Procedure: Basic instructions to perform commercial load calculations, on buildings of three stories or less. Supports a simplified hand calculation.
• Section 2 Advanced Topics: Provides enhanced procedures, capabilities, and sensitivities (requires computer software to process).
• Section 3 Tables: Provides input for the worksheets and determinations needed for the abridged (N5ae) and full (N5) procedures.
• Section 4 Appendices: Provides supporting materials and details on the N5ae and N5 applications...(640 pages)

Manual D includes a number of informative appendices related to air distribution systems (e.g., equipment and air-side components, controlling excess air when VAV dampers close, duct loads, duct leakage and duct system efficiency, air quality issues, noise control, minimum air velocity for ducts; codes, standards and best practice issues; and commissioning issues). The Manual D has been significantly revised to include:

• Updated and expanded VAV guidance, with detailed examples
• Impacts of excess length, sag and compression in flexible ducts
• New equivalent length values for flex duct junction boxes

Manual D provides:

• A single set of ANSI-recognized duct sizing principles and calculations that apply to all duct materials
• System operating point (supply Cfm and external static pressure), and airway sizing for single-speed and multi-speed (ECM) blowers
• A method for determining the impact of duct friction and fitting pressure drop on blower performance and air delivery
• The most comprehensive equivalent length data ever published

You can apply the Manual D procedure to constant volume systems and zoned variable air volume systems, over a full range of duct construction materials. Manual D includes a number of informative appendices related to air distribution systems (e.g., equipment and air-side components, controlling excess air when VAV dampers close, duct loads, duct leakage and duct system efficiency, air quality issues, noise control, minimum air velocity for ducts; codes, standards and best practice issues; and commissioning issues).

Manual J 8th Edition is the national ANSI recognized standard for producing HVAC equipment sizing loads for single-family detached homes, small multi-unit structures, condominiums, town houses, and manufactured homes. A proper load calculation, performed in accordance with the Manual J 8th Edition procedure, is required by national building codes and most state and local jurisdictions.

Modern Refrigeration and Air Conditioning, 22nd Edition is focused on closing the gap from students to technicians with our commitment to top-quality coverage of fundamentals and the latest technology. This classic is an excellent blend of theory, skill development, and service techniques to help you learn how to install and service refrigeration and HVAC systems.

Updated through January 2023, the book provides a comprehensive set of the most up-to-date Construction regulations. Utilizing MANCOMM’s signature formatting approach – RegLogic – this edition includes notations for changes within the past year and letters of reference.

This book features:

• 1903 – Inspections, Citations, and Penalties
• Part 1904 – Recording and Reporting Occupational Illnesses and Injuries
• Selected 1910 General Industry Standards
• OSHA Forms 300
• Sharps Injury Log
• This edition also includes Subpart AA - Confined Spaces

Compact and pocket-sized, this handy reference contains thousands of facts and figures relevant to pipefitters, steamfitters-anyone concerned with layout and installation of pipe.

Custom Tab Bundle, please specify which books these tabs should reference at checkout