Nevada B - General Building Contractor License

This code applies to all buildings except detached one- and two-family dwellings and townhouses up to three stories. The 2018 IBC contains many important changes such as:

• Accessory storage spaces of any size are now permitted to be classified as part of the occupancy to which they are accessory.
• New code sections have been introduced addressing medical gas systems and higher education laboratories.
• Use of fire walls to create separate buildings is now limited to only the determination of permissible types of construction based on allowable building area and height.
• Where an elevator hoistway door opens into a fire-resistance-rated corridor, the opening must be protected in a manner to address smoke intrusion into the hoistway.
• The occupant load factor for business uses has been revised to one occupant per 150 square feet.
• Live loads on decks and balconies increase the deck live load to one and one-half times the live load of the area served.
• The minimum lateral load that fire walls are required to resist is five pounds per square foot.
• Wind speed maps updated, including maps for the state of Hawaii.
• Terminology describing wind speeds has changed again with ultimate design wind speeds now called basic design wind speeds.
• Site soil coefficients now correspond to the newest generation of ground motion attenuation equations (seismic values).
• Five-foot tall wood trusses requiring permanent bracing must have a periodic special inspection to verify that the required bracing has been installed.
• New alternative fastener schedule for construction of mechanically laminated decking is added giving equivalent power-driven fasteners for the 20-penny nail.
• Solid sawn lumber header and girder spans for the exterior bearing walls reduce span lengths to allow #2 Southern Pine design values.

The Code covers the design and construction of masonry structures, with subjects covered ranging from quality assurance to the details and development of reinforcement. Compliance with the Specification is required by the Code to control materials, labor and construction.

The “Building Code Requirements for Structural Concrete” (“Code”) provides minimum requirements for the materials, design, and detailing of structural concrete buildings and, where applicable, nonbuilding structures. This Code addresses structural systems, members, and connections, including cast-in-place, precast, plain, nonprestressed, prestressed, and composite construction. Among the subjects covered are: design and construction for strength, serviceability, and durability; load combinations, load factors, and strength reduction factors; structural analysis methods; deflection limits; mechanical and adhesive anchoring to concrete; development and splicing of reinforcement; construction document information; field inspection and testing; and methods to evaluate the strength of existing structures. “Building Code Requirements for Concrete Thin Shells” (ACI 318.2) is adopted by reference in this Code.The Code user will find that ACI 318-14 has been substantially reorganized and reformatted from previous editions. The principal objectives of this reorganization are to present all design and detailing requirements for structural systems or for individual members in chapters devoted to those individual subjects, and to arrange the chapters in a manner that generally follows the process and chronology of design and construction. Information and procedures that are common to the design of members are located in utility chapters.

The quality and testing of materials used in construction are covered by reference to the appropriate ASTM standard specifications. Welding of reinforcement is covered by reference to the appropriate American Welding Society (AWS) standard. Uses of the Code include adoption by reference in a general building code, and earlier editions have been widely used in this manner. The Code is written in a format that allows such reference without change to its language. Therefore, background details or suggestions for carrying out the requirements or intent of the Code provisions cannot be included within the Code itself. The Commentary is provided for this purpose. Some of the considerations of the committee in developing the Code are discussed within the Commentary, with emphasis given to the explanation of new or revised provisions. Much of the research data referenced in preparing the Code is cited for the user desiring to study individual questions in greater detail.

Updated through January 2023, the book provides a comprehensive set of the most up-to-date Construction regulations. Utilizing MANCOMM’s signature formatting approach – RegLogic – this edition includes notations for changes within the past year and letters of reference.

This book features:

• 1903 – Inspections, Citations, and Penalties
• Part 1904 – Recording and Reporting Occupational Illnesses and Injuries
• Selected 1910 General Industry Standards
• OSHA Forms 300
• Sharps Injury Log
• This edition also includes Subpart AA - Confined Spaces

The digest includes descriptions of the standard products: K-Series joists, LH/DLH-Series joists, Joist Girders and now CJ-Series joists, how joist products are prepared, tagged, loaded and shipped from the joist manufacturers plant, how they are to be unloaded and stored at the job site, how the joist products are to be erected including bridging, and field inspection. Other topics covered in the digest are panelized erection and common field issues.

This edition contains information related to the newest standard joist product, the CJ-Series joists that were introduced in 2007. It also includes updated information on Bridging in Chapter 8 as well as some additional topics added to the list of Miscellaneous Topics - Common Field Issues in Chapter 9.

General contractors, steel erectors, inspectors, and building officials would most benefit from this Technical Digest. Engineers and Architects would also benefit from the information contained in the digest if part of their responsibilities is to oversee joist and Joist Girder projects under construction.

Includes hands-on instructions for operating the equipment and doing the trenching, pipe laying and connecting work and answers to what causes so many skilled equipment operators and pipe layers to fail when they try to start their own business.

Learn how to find the right kind of work, read and compute quantities from the plans, figure realistic crew and equipment productivity rates, consider job variables, calculate your O & P, then estimate and bid the job, and get the bonds you need. Also, how to deal with change orders and liquidated damages, choosing the right equipment, and handling safety issues.

When it comes to doing the actual work, you ll find the combined expertise of two long-time professionals, explaining how to follow and read the surveyor s reference stakes; how to check grade and line with an optical level, transit and pipe laser, and how to use GPS systems. See the best ways to clear the site, including asphalt and rock; handle rock, steep slopes and high groundwater; meet compaction requirements; install septic tanks and drain fields; all common types of water and sewer pipe, and how to do subsurface excavation.

Drywall, joint compound, backerboard, plaster finishes, ceiling panels, sheathing gypsum-based products are essential for construction jobs large and small. From the planning process all the way down to the jobsite, understanding how and when to correctly use gypsum materials can mean the difference between a job well done and a construction nightmare. Since 1905, The Gypsum Construction Handbook has been the standard manual for construction professionals.

New materials, new methods, and new requirements demand new approaches, plain and simple. The gypsum revolution changed the world of building construction, and The Gypsum Construction Handbook has kept up with innovation in the industry ever since. This Seventh Edition update includes essential guidelines for using state-of-the art USG products, including innovative ultralight, sustainable, and low-dust materials.

USG has been the global leader in gypsum construction products for over a century, and the company employs the world’s premier experts on building with gypsum. These experts are the people who designed the leading products in the industry, and they are the people who wrote the book on how to use them.

This book includes detailed instructions for using USG products, including:

• USG Securock Brand Glass-Mat Sheathing
• USG Sheetrock Products
• USG Fiberock Panels
• USG Ceilings Brand Clean Room ClimaPlus Acoustical Panels
• USG Durock & Accessory Products
• USG Imperial & Diamond Brand Plasters

In addition, you’ll find general construction best practices for everything from framing to finishing. The Gypsum Construction Handbook also contains all the essentials on health, safety, code, and sustainability.

This instructional manual has been prepared by the Post-Tensioning Institute's Committee for Training and Certification of Field Personnel for Unbonded Post-Tensioning soley as a recommended general guide and assistance to the placement, installation and inspection of unbonded single strand post-tensioning systems, the operation of stressing equipment, and accessories.

Code features reference the International Residential Code and International Building Code, familiarizing students with their requirements. Updated, color images have been added throughout the text to reinforce chapter topics. Over 75 illustrated step-by-step procedures guide student learning.

This document is published jointly by the American Concrete Institute (ACI) and the American Society of Concrete Contractors (ASCC). It has been reviewed in accordance with the Educational Committee Manual document review procedures of the ACI Educational Activities Committee. ACI and ASCC reports are intended for guidance in planning, designing, executing, and inspecting construction. This document is intended for the use of individuals who are competent to evaluate the significance and limitations of its content and recommendations and who will accept responsibility for the application of the material it contains. A summary, review questions, and additional recommended reading list accompany each of the 12 chapters.

Custom Tab Bundle, please specify which books these tabs should reference at checkout

Prepared for the Nevada Construction Business and Law Exam as a study guide and open book reference.

The general business and law or “CMS” exam is open book and this book is allowed to be taken with you when you sit for the exam.

The book is organized into 3 sections.

Part 1 focuses on business planning and start up. This section will help you formulate a business plan, choose a business structure, understand licensing and insurance requirements and gain basic management and marketing skills.

Part 2 is centered on fundamentals that you will need to operate a successful construction business. This section will cover estimating, contract management, scheduling, project management, safety and environmental responsibilities and building good relationships with employees, subcontractors and customers.

Part 3 gives you valuable information for running the administrative function of your business. Financial management, tax basics and lien laws are covered. Effective management of these areas of business is vital and can cause serious problems if you do not give them the proper attention.

Custom Tab Bundle, please specify which books these tabs should reference at checkout